I used the Split tool on Parcels_011224 with DFIRM_FloodHazardAreas_BlockIsland_EPSG3438 with OBJECTID_2 as the split feature. I then appended the split shapefiles back together. I created a FloodHazard_ZoneSubtype_Split Field to identify the flood hazard risk for the split feature. FloodHazard provides a Y/N field for risk. Areas with minimal flood risk were determined to be a N and areas with 0.2 Percent or higher were determined to be a Y.

---

See below for the Parcels_011224 Description

Downloaded from: https://bigis.maps.arcgis.com/home/webmap/viewer.html?webmap=3a1af4669dec4c1484a4165fa9614e0e

A Y value for the IntWetland attribute means the parcel intersects with NationalWetlandsInventory_BlockIsland_EPSG3438_Merged. A Y value for the IntWetlandBuffer attribute means the parcel intersects with NationalWetlandsInventory_BlockIsland_EPSG3438_BufferOnly.

Note some parcel features overlap with other parcel features. OBJECTID 877 (AV_PID 2141) overlaps with OBJECTID 0 (AV_PID 184552).

Many parcels only minorly overlap with LocalConservationAreas_BlockIsland_EPSG3438. A Full value for the IntLocConsAreaVerified means the parcel appears like it should fully overlap with the LocalConservationAreas_BlockIsland_EPSG3438. A Partial value for the IntLocConsAreaVerified means the parcel appears like it should only partially overlap with the LocalConservationAreas_BlockIsland_EPSG3438. For example there might be a cutout in the center for a home, or only half the parcel is conserved. These features can also be found in Parcels_011224_IntLCA_ManuallyVerified in the Conserved Lands feature dataset.

Many parcels only minorly overlap with StateConservationAreas_BlockIsland_EPSG3438. A Full value for the IntStaConsAreaVerified means the parcel appears like it should fully overlap with the StateConservationAreas_BlockIsland_EPSG3438. A Partial value for the IntStaConsAreaVerified means the parcel appears like it should only partially overlap with the StateConservationAreas_BlockIsland_EPSG3438. For example there might be a cutout in the center for a home, or only half the parcel is conserved. These features can also be found in Parcels_011224_IntSCA_ManuallyVerified in the Conserved Lands feature dataset.

A few parcels only minorly overlap with NationalConservationAreas_BlockIsland_EPSG3438. A Full value for the IntNatConsAreaVerified means the parcel appears like it should fully overlap with the NationalConservationAreas_BlockIsland_EPSG3438. A Partial value for the IntNatConsAreaVerified means the parcel appears like it should only partially overlap with the NationalConservationAreas_BlockIsland_EPSG3438. For example there might be a cutout in the center for a home, or only half the parcel is conserved. These features can also be found in Parcels_011224_IntNCA_ManuallyVerified in the Conserved Lands feature dataset.

The FloodHazard_ZoneSubtype attribute represents the flood hazard for each parcel, based on overlap with DFIRM_FloodHazardAreas_BlockIsland_EPSG3438 and the ZONE_SUBTY attribute. These are ordered by level of risk. "Partial" means that only a part of the full parcel contains this flood hazard type & "Full" means the entire parcel is under this flood hazard type.

The ZoningDistrict attribute represents the Zoning District for each parcel, based on overlap with ZoningDistricts_BlockIslandEPSG3438. Note these two layer boundaries did not completely align so I used manual verification. I set the PD zones to PD_NHC and PD_RC, assuming each PD area had the same setbacks as NHD & RC respectively.

Setback_Conservative represents the largest minimum setback value identified in the New Shoreham zoning ordinance (see here Appendix C in this document: https://clerkshq.com/NewShoreham-RI?docId=NShoreAppE&path=NewShoreham_Code%2CNShoreP2%2CNShoreAppE%2C). Rear, Side, and Front setbacks are not distinguished here. I assumed the PD zone near the New Harbor Commercial had NHC setback rules and the PD zone near the Residential C Zone had RC setback rules.

Auto-assigned IDs to allow for publishing as a web layer.